top of page
cropped-QuiltEZ-Logo-2048x2048.png

Move

move

Editing Tools

Feature Library

Move

Reposition a design, nudge it, or center it.

The Move tool repositions a design in your layout box. Buttons center the design on the vertical or horizontal, or move it one increment at a time with the increment size set in Settings (for example 0.1 inch). You can also drag with the green node, use Move Start to reposition where the pattern begins, and move several copies of a design together as a group. Move is also what you use to realign a design after reopening a saved layout.

Watch and learn · 11 videos

  • Nesting from a Saved Design · 19:09

    Restarts nesting from a saved design after a break. Opens the saved layout from the Layout screen, uses Move in Edit to line the design back up in the layout box, and then goes to Nesting to mark the nesting point and confirm a new nested row. Reminds viewers to double-check the needle is out of the fabric before starting.

  • Manual Nesting with the Amethyst Butler · 17:03

    Shows how to nest manually on the Amethyst, which doesn't include the Nesting feature. Stays on the home screen, lines the second row up by hand, and repeats the process row by row to the end of the quilt. Points viewers to the Sapphire, Emerald or Ruby if they want automatic nesting.

  • Set Up E2E Using Edit Features · 21:13

    Sets up an edge-to-edge layout from scratch using only editing features. Uses Repeat to make rows of a rose design, Scale to fit them in the layout area, Move to offset the rows, Crop to trim the edges, and Merge to combine the pieces. Checks in Settings that jump stitches are turned on because cropping cuts off parts of the design.

  • Crop, Record, Move & Jump Stitches · 18:30

    Covers quilting a large panel by combining Crop, Move and jump-stitch settings. Crops everything outside the box, sets a maximum jump-stitch length (about six to eight inches here), and walks through the prompts to turn stitching off and on at each jump. Explains why the extra steps are tedious but necessary to get a clean crop.

  • Quilt Along with Aubrey, Part 3 · 16:24

    Part three of the quilt-along, finishing the jelly-roll strip quilt. Reopens the saved "strip quilt" layout, then checks the alignment by moving the crosshairs to the top-left corner of the layout box and traveling to the stop point to confirm it falls just inside the quilt edge. Shows why saving a layout is useful for big quilts that take more than one day.

  • Channel Locks (2024, Ep 43) · 15:38

    Explains the channel locks on mid- and top-tier Butler systems, found on the Home screen. The horizontal lock keeps the machine moving only side to side, the vertical lock only forward and back, and the diagonal lock along a diagonal. Useful for straight-line quilting, filler work, and cross-hatching.

  • Offset an E2E Design While Nesting · 17:57

    Shows how to offset an edge-to-edge design while nesting, a technique a customer asked about. Because the machine lacks throat space to stitch two offset rows at once, you stitch one row at a time and use the Edit screen's Repeat and Move tools to offset the design before nesting the next row into the gaps. Includes marking the nesting point and leaving enough room to roll the quilt.

  • Modify Feature (2024, Ep 36) · 15:05

    Shows how the Modify button speeds up quilts with repeated blocks. After editing a design to fit one block, use Modify to move the layout area to the next identical block by setting its corners, and the edited design carries over. The example fills the large focus blocks of a Halloween quilt, including turning the stitching on at the long arm when prompted.

  • Save, Close & Reopen a Layout — Q&A · 16:18

    A follow-up Q&A on saving layouts. Sets a layout, scales it with smart scale so it does not distort, saves it from the Layout screen, then checks the file folder to confirm the layout is listed. Reopens the saved layout and continues into nesting, with the point that a saved layout always lets you return to the top-left reference spot.

  • Move Feature · 14:15

    Explains the Move tool in detail. Buttons move a design to the center of the vertical or horizontal, or one increment at a time, with the increment size set in Settings (for example 0.1 inch). You can also drag with the green node, use Move Start to reposition where the pattern begins, and move several copies of a design together as a group.

  • Adjusting Patterns Within Nesting · 9:16

    Shows how to use the Move tool during nesting when a design with lots of dips and curves needs a small adjustment. Run the normal nesting steps, mark the nesting point, roll the quilt, and then nudge the design into place before confirming. Reminds you to check that the needle is up before the machine moves to the nesting point.

Common questions

How do I center a design?

Open Move and use the centering buttons for vertical and horizontal. The Margins video uses them to center a design with an even half-inch margin all the way around.

Can I change how far each nudge moves the design?

Yes. The increment is set in Settings, for example 0.1 inch.

What does Move Start do?

It lets you reposition where the pattern begins.

bottom of page