top of page
cropped-QuiltEZ-Logo-2048x2048.png

Edge-to-Edge

edge-to-edge

Layout & Stitching

Feature Library

Edge-to-Edge

Fill the whole quilt with one repeating design.

An edge-to-edge (E2E) design runs across the full quilt top, row after row. On the Butler you set a layout box for the quilt top, pick a design, use Repeat to fill the width, and stitch out each pass, using Nesting to line the rows up. There is no single right way to place an edge-to-edge design: you can use the safe area, a layout box, or Autofill. These videos show simple E2E setups, building an E2E layout from editing features alone, and quilting small projects. They also include an introduction to the Amethyst, the model designed for edge-to-edge quilting.

Watch and learn · 12 videos

  • Edge to Edge Bonus Project · 10:21

    Quilts a small bonus project from leftover fabric using an edge-to-edge design. Sets the layout about a quarter inch outside the quilt edge, uses Repeat and Auto Scale to fit the design, and adjusts stitching speed (20 is the default; around 30 is typical for an average project).

  • E2E Setup with Edit Features & USB Pattern Load · 17:13

    Loads a purchased pattern from a USB stick, assigns it to a custom tag, and finds it in the Patterns tab. Then uses Repeat to fill the layout, turns on the proportion lock so circles stay circular, uses Auto Scale, and moves the design into place before stitching out an edge-to-edge layout.

  • Flag Quilt: USB Import, E2E Setup & Quilting · 17:30

    Sets up and quilts a flag-style quilt. Imports a pattern from a USB stick using the external storage location and assigns it to a custom tag, sets the layout points just above and left of the quilt top, scales the design, and travels across the quilt to begin. Suggested for time-crunched holiday and Quilts of Valor projects.

  • Introduction to the Amethyst Butler · 13:50

    Introduces the Amethyst, an edge-to-edge-only model in the Butler lineup with simplified features and 120 patterns preloaded (more can be imported). Shows setting up a layout, choosing a pattern, using Repeat and stitching out a quilt. Notes that some features on the Sapphire, Emerald and Ruby models are not available on this one.

  • Set Up E2E & Import a Pattern · 20:28

    Sets up an edge-to-edge quilt from start to finish. Sets the layout points for the quilting space, then imports a purchased design in the Import/Export tab and assigns it to a custom tag instead of the default Imported tag. Shows how to find it afterward in the Patterns tab (listed numerically, then alphabetically) and add it to the layout.

  • Set Up E2E Using Edit Features · 21:13

    Sets up an edge-to-edge layout from scratch using only editing features. Uses Repeat to make rows of a rose design, Scale to fit them in the layout area, Move to offset the rows, Crop to trim the edges, and Merge to combine the pieces. Checks in Settings that jump stitches are turned on because cropping cuts off parts of the design.

  • Nesting E2E in Quilt Center & Custom Quilting · 14:14

    Nests an edge-to-edge design into the center of a quilt that already has custom borders. Opens Nesting from the home screen, drops the needle into the fabric at a low point to mark the nesting point, rolls the quilt, and confirms. Continues nesting row by row down the center panel until it's filled.

  • E2E & Nesting · 17:59

    A refresher on nesting for an edge-to-edge quilt. After finishing the first row, opens Nesting from the home screen, marks a nesting point on the quilt top, rolls the quilt, and re-hovers over the point. Explains what to do if the point was marked with a pen and when to stitch down the sides.

  • New Quilt & E2E Design · 14:53

    Sets up a new quilt for an edge-to-edge design. Marks the quilting area, accounts for the quilt shrinking the available space as it rolls onto the back roller bar, nudges the design to fill an empty corner, and stitches out. Also mentions where to find the patterns used in the video.

  • Third Row of an Offset E2E Nesting Design · 5:46

    Follows the offset edge-to-edge nesting video by working through the third row. Nest as normal, then use Edit to remove the extra design hanging off the end. Rows alternate in count: the first row had five designs, the second six, and the third back to five, so you add or subtract a design every other row.

  • Offset an E2E Design While Nesting · 17:57

    Shows how to offset an edge-to-edge design while nesting, a technique a customer asked about. Because the machine lacks throat space to stitch two offset rows at once, you stitch one row at a time and use the Edit screen's Repeat and Move tools to offset the design before nesting the next row into the gaps. Includes marking the nesting point and leaving enough room to roll the quilt.

  • Edge to Edge · 11:06

    A simple edge-to-edge setup on a small gift quilt about 42 by 45 inches. Sets the layout box roughly a quarter inch outside the quilt top, picks a swirl-and-pearl edge-to-edge design, and uses the Repeat tool's horizontal repeat to fill the box. Stresses there is no right or wrong way to place an edge-to-edge design: use the safe area, a layout box, or autofill.

Common questions

How do I set up an edge-to-edge design?

Set a layout box for the quilt top (a quarter inch outside the quilt top is used in the videos), choose a design, and use Repeat to fill the box. Use Auto Scale to fit the design if you need to, then stitch out the first row and nest the rest.

Do I have to use the safe area or a layout box?

No. The Edge to Edge video stresses that there is no right or wrong way: you can use the safe area, a layout box, or Autofill. Pick whichever works for your quilt.

What is the Amethyst model?

The Amethyst is an edge-to-edge-only model in the Butler lineup with simplified features and 120 patterns already loaded. It does not include Nesting, so rows are lined up manually. The introduction and manual nesting videos cover it.

bottom of page